[Arm-netbook] eoma68-a20 ethernet testing

[joem]

Actually Mr Luke, you have a bug in your documentation.

Where it says 
  ./usb-boot ../u-boot-sunxi/spl/u-boot-spl.bin ../u-boot/u-boot.bin

it should read
  ./usb-boot ../u-boot-sunxi/spl/u-boot-spl.bin ../u-boot-sunxi/u-boot.bin



After correcting for that, I get:

  # That is the EOMA. To check it is working, do this:

  cd sunxi-tools
  sudo ./usb-boot ../u-boot-sunxi/spl/u-boot-spl.bin ../u-boot-sunxi/u-boot.bin

  # ordinarily sudo is not needed in above line, it seems USB on Ubuntu 12.04 is broken.
  # note ./usb-boot takes two parameters, both of which were previously compiled
  # and sitting in u-boot-sunxi directory.
  # The messages I get when ./usb-boot runs are these:

fel write 0x2000 ../u-boot-sunxi/spl/u-boot-spl.bin
fel exe 0x2000
fel write 0x4a000000 ../u-boot-sunxi/u-boot.bin
fel write 0x41000000 ./bin/ramboot.scr
fel exe 0x4a000000

  # and on the minicom window, I get these messages:

U-Boot SPL 2013.10-rc1-08247-gd787d30 (Sep 04 2013 - 10:03:46)
Board: EOMA68_A20_FEL
DRAM: 1024 MiB
CPU: 960000000Hz, AXI/AHB/APB: 3/2/2

U-Boot 2013.10-rc1-08247-gd787d30 (Sep 04 2013 - 10:03:46) Allwinner Technology 
                                                                                
CPU:   Allwinner A20 (SUN7I)                                                    
Board: EOMA68_A20_FEL                                                           
I2C:   ready                                                                    
DRAM:  1 GiB                                                                    
MMC:   SUNXI SD/MMC: 0                                                          
Card did not respond to voltage select!                                         
MMC init failed                                                                 
Using default environment                                                       
                                                                                
In:    serial                                                                   
Out:   serial                                                                   
Err:   serial                                                                   
Net:   emac                                                                     
Hit any key to stop autoboot:  0                                                
## Executing script at 41000000                                                 
                                                                                
## Checking Image at 4c000000 ...                                               
Unknown image format!                                                           
Wrong Image Format for bootm command                                            
ERROR: can't get kernel image!                                                  
Card did not respond to voltage select!                                         
** Bad device mmc 0 **                                                          
Card did not respond to voltage select!                                         
** Bad device mmc 0 **                                                          
Card did not respond to voltage select!                                         
** Bad device mmc 0 **                                                          
Card did not respond to voltage select!                                         
** Bad device mmc 0 **                                                          
Card did not respond to voltage select!                                         
** Bad device mmc 0 **                                                          
Card did not respond to voltage select!                                         
** Bad device mmc 0 **                                                          
Card did not respond to voltage select!                                         
** Bad device mmc 0 **                                                          
Card did not respond to voltage select!                                         
** Bad device mmc 0 **                                                          
Card did not respond to voltage select!                                         
** Bad device mmc 0 **                                                          
sun7i# 


----

Is that about right to do next steps?



_______________________________________________
arm-netbook mailing list arm-netbook at lists.phcomp.co.uk
http://lists.phcomp.co.uk/mailman/listinfo/arm-netbook
Send large attachments to arm-netbook at files.phcomp.co.uk