[Arm-netbook] EOMA68-A20 usb fel-boot and u-boot upload (no GPL-violating allwinner boot0 or boot1 involved)

Tom Cubie mr.hipboi at gmail.com
Tue Jun 4 13:19:51 BST 2013


On Mon, Jun 3, 2013 at 9:00 PM, Neal Peacock <neal at nic-stix.com> wrote:
>
> On 05/31/2013 07:49 PM, luke.leighton wrote:
>>
>> http://hands.com/~lkcl/eoma/eoma68-a20-uboot.patch
>> mess but it works.  A20 is more like SUN5I.  kernel doesn't boot yet,
>> possibly due to watchdog timer issue, TBD tomorrow.
>
> Since everyone seems to be feeling argumentative today I figured I would
> bring this up.
>
> Is there any evidence boot0/boot1 are GPL violating?  What GPL code that is
> not owned by Allwinner do you think is included?

No, the boot0/boot1 code is completely by allwinner themselves.

>
>
>>
>> l.
>>
>> -------------
>> U-Boot SPL 2013.04-06937-g4a60715-dirty (Jun 01 2013 - 00:35:33)
>> Board: EOMA68_A20
>> DRAM:dramc_init pre setup clock
>> dramc_init pre disable pad power
>> dramc_init pre ddr3 reset
>> dramc_init pre set drive
>> dramc_init clock off
>> post select dram, csel = 0x86c9883
>> dramc_init clock pre itm disable
>> dramc_init clock pre enable dll0
>> dramc_init configure external dram
>> dramc_init external dram reg written
>> dramc_init set impedance
>> dramc_init clock on
>> dramc_init wait for ccr
>> dramc_init enable dllx
>> dramc_init set iocr
>> dramc_init set refresh period
>> dramc_init set timings
>> dramc_init set mode
>> dramc_init set dqs
>> dramc_init reset dram
>> dramc_init scan read pipe
>> dramc_init read pipe: 0
>> dramc_init configure hostport
>> dramc_init configured hostport, getting ramsize
>> dramc_init got ramsize 1073741824
>>   1024MB
>>
>>
>> U-Boot 2013.04-06937-g4a60715-dirty (Jun 01 2013 - 00:35:33) Allwinner
>> Technoloy
>>
>> CPU:   SUNXI Family
>> Board: EOMA68_A20
>> I2C:   ready
>> DRAM:  1 GiB
>> MMC:   SUNXI SD/MMC: 0
>> MMC Device 3 not found
>> No MMC card found
>> Using default environment
>>
>> In:    serial
>> Out:   serial
>> Err:   serial
>> Net:   wemac
>> Hit any key to stop autoboot:  0
>> reading uEnv.txt
>> 188 bytes read in 10 ms (17.6 KiB/s)
>> Loaded environment from uEnv.txt
>> reading boot.scr
>> 579 bytes read in 3 ms (188.5 KiB/s)
>> Jumping to boot.scr
>> ## Executing script at 44000000
>> Failed to mount ext2 filesystem...
>> ** Unrecognized filesystem type **
>> reading script.bin
>> 43084 bytes read in 7 ms (5.9 MiB/s)
>> reading uImage
>> 3355592 bytes read in 171 ms (18.7 MiB/s)
>> ## Booting kernel from Legacy Image at 48000000 ...
>>     Image Name:   Linux-3.3.0
>>     Created:      2013-05-29  20:27:05 UTC
>>     Image Type:   ARM Linux Kernel Image (uncompressed)
>>     Data Size:    3355528 Bytes = 3.2 MiB
>>     Load Address: 40008000
>>     Entry Point:  40008000
>>     Verifying Checksum ... OK
>>     Loading Kernel Image ... OK
>> OK
>>
>> Starting kernel ...
>>
>>
>> Error: unrecognized/unsupported machine ID (r1 = 0x00001008).
>>
>> Available machine support:
>>
>> ID (hex)        NAME
>> 00000f35        sun7i
>>
>> Please check your kernel config and/or bootloader.
>>
>> _______________________________________________
>> arm-netbook mailing list arm-netbook at lists.phcomp.co.uk
>> http://lists.phcomp.co.uk/mailman/listinfo/arm-netbook
>> Send large attachments to arm-netbook at files.phcomp.co.uk
>
>
> --
> Neal Peacock
> PengPod
>
>
>
> _______________________________________________
> arm-netbook mailing list arm-netbook at lists.phcomp.co.uk
> http://lists.phcomp.co.uk/mailman/listinfo/arm-netbook
> Send large attachments to arm-netbook at files.phcomp.co.uk



-- 
Keep simple, stay foolish.



More information about the arm-netbook mailing list