I meant the patch has the link truncated
On Fri, Nov 1, 2013 at 10:31 PM, luke.leighton luke.leighton@gmail.comwrote:
talk to joe ok? really busy martin. rev3 pcb, doing the routing myself (1st board. scarey!)
On Fri, Nov 1, 2013 at 10:01 PM, martin brook martin.brook100@googlemail.com wrote:
Luke Hi,
Has the text been truncated there? "http://www.gplsquared.com/eoma_boot/script.fex_2013_09_17"
On Fri, Nov 1, 2013 at 9:22 PM, luke.leighton luke.leighton@gmail.com wrote:
good enough, martin - thank you :)
diff --git a/allwinner/a20/boot.mdwn b/allwinner/a20/boot.mdwn index 541a69b..d3b0c70 100644 --- a/allwinner/a20/boot.mdwn +++ b/allwinner/a20/boot.mdwn @@ -1,6 +1,9 @@ # config files
<a href="./script.fex">script.fex</a><br />
+I had more luck with this fex, http://www.gplsquared.com/eoma_boot/script.fex_2
<a href="./eoma68-a20-3.3-config">eoma68-a20-3.3-config</a> <br /> <a href="./eoma68-a20-3.4-config">eoma68-a20-3.4-config</a> <br />
On Wed, Oct 30, 2013 at 2:05 PM, luke.leighton <luke.leighton@gmail.com
wrote:
great, martin - can you add that to the wiki plese? anyhow you can. thanks
On Wed, Oct 30, 2013 at 6:35 AM, martin brook martin.brook100@googlemail.com wrote:
I had more luck with this .fex http://www.gplsquared.com/eoma_boot/script.fex_2013_09_17
On Wed, Oct 30, 2013 at 6:00 AM, luke.leighton luke.leighton@gmail.com wrote:
On Wed, Oct 30, 2013 at 2:08 AM, Ryan Mullen rmmullen@gmail.com wrote: > Hi, > > I am booting an eoma68-a20 using the script.fex (converted to > script.bin with sunxi-tools' fex2bin) found here: > > http://rhombus-tech.net/allwinner/a20/boot/script.fex > > I have run the instructions found on that page under the subtitle > "setup boot instructions for booting directly off of sd/mmc" and
all
> seems well. > > However, my kernel (linux-sunxi 3.4 with some custom config
options)
> tells me this when booting: > > [ 1.663649] [mmc-msg] sw_mci_init > [ 1.667156] [mmc-msg] get mmc1's IO(det) failed > [ 1.671684] [mmc-msg] Not using mmc1 due to script.bin parse > failure > [ 1.678123] [mmc-msg] MMC host used card: 0x9, boot card: 0x0, > io_card 8 > [ 1.685471] [mmc-msg] sdc0 set round clock 400000, src 24000000 > [ 1.691708] [mmc-msg] sdc0 set ios: clk 0Hz bm OD pm OFF vdd
3.3V
> width 1 timing LEGACY(SDR12) dt B > [ 1.702062] [mmc-msg] sdc0 Probe: base:0xf0034000 irq:64 > sg_cpu:ffdfb000(4fc00000) ret 0. > [ 1.710382] [mmc-msg] sdc3 set round clock 400000, src 24000000 > [ 1.716717] [mmc-msg] sdc3 set ios: clk 0Hz bm OD pm OFF vdd
3.3V
> width 1 timing LEGACY(SDR12) dt B > [ 1.726839] [mmc-msg] sdc3 Probe: base:0xf0036000 irq:67 > sg_cpu:ffdfa000(4fc01000) ret 0. > > After I boot an initrd, there are no /dev/mmcblk0 entries in my
dev
> filesystem. However, I can make it appear if I do the following: > > echo 1 > /proc/driver/sunxi-mmc.3/insert > > This causes the card to be registered at /dev/mmcblk0 as expected. > > Digging deeper, it would seem that the script.fex sets the > card-detect > mode for mmc0 and mmc1 both to 1, which is CARD_DETECT_BY_GPIO.
The
> failure in the kernel log occurs when the script.bin parser tries
to
> read the "sdc_det" key and doesn't get a valid value describing
the
> GPIO it should be using, I assume. mmc3 doesn't have that problem > because script.fex sets the card-detect mode to 4, which is manual > mode - this requires me to write a 1 to the control node in the > procfs > as I experienced. > > Is the script.fex incomplete?
almost certainly!
> What's going on here?
we're reliant on you to help diagnose that! can you please check
the
GPIO line when the card is inserted, by using the gpio kernel module (use 3.4 it's easier) flipping it to input and reading the entry?
it
could be that the manual-soldering of the mmc card slot was done poorly.
l.
arm-netbook mailing list arm-netbook@lists.phcomp.co.uk http://lists.phcomp.co.uk/mailman/listinfo/arm-netbook Send large attachments to arm-netbook@files.phcomp.co.uk
arm-netbook mailing list arm-netbook@lists.phcomp.co.uk http://lists.phcomp.co.uk/mailman/listinfo/arm-netbook Send large attachments to arm-netbook@files.phcomp.co.uk
arm-netbook mailing list arm-netbook@lists.phcomp.co.uk http://lists.phcomp.co.uk/mailman/listinfo/arm-netbook Send large attachments to arm-netbook@files.phcomp.co.uk
arm-netbook mailing list arm-netbook@lists.phcomp.co.uk http://lists.phcomp.co.uk/mailman/listinfo/arm-netbook Send large attachments to arm-netbook@files.phcomp.co.uk
arm-netbook mailing list arm-netbook@lists.phcomp.co.uk http://lists.phcomp.co.uk/mailman/listinfo/arm-netbook Send large attachments to arm-netbook@files.phcomp.co.uk